We Provide The Best Service For You
Aquacoat
- Home
- Waterproofing
- Aquacoat
Our Product
Aquacoat Products
Main Application
- Non-exposed roof,
- Underground,
- Indoor bathroom and kitchen and
- Inedible pool waterproof construction
Installation
Substrate Preparation
All Surfaces
The substrate needs to be strong and smooth, clean and dry. Fill the holes with cement mortar. The aws such as honey comb should also be repaired. The external and internal corner are made to be arc. Internal corner: D50mm External corner: D10mm. Brush the rst layer then pave the non-woven reinforced layer. Permeate the reinforced layer with the material thoroughly.
Application
Firstly apply the stirred polyurethane waterproong coating over special positions like the external and internal reinforcement as well as the orice of the through-wall pipe. After meeting the requirement, make the widespread coating. Use brush or rubber scraper to brush the substrate evenly. Apply the second layer provided the rst layer is cured. The coating direction is vertical to the rst one and then the third layer’s direction is the same as the rst one. Brush repeatedly till meets the designed thickness. After curing, it will form a complete seamless waterproof rubber lm which is bond strongly to the substrate. Before the next procedure, pay attention not to damage the waterproong membrane with
hard objects in case of invalidation of the waterproong. If damaged, notify the constructor to repair it.
The interval time: it depends on the application site but typically the surface drying time is about 12 hours.
The actual interval time is based on that the previous layer is tack-free.
Aquacoat QL -929
Single Component, Moisture Cured,100% PolyurethaneWaterproong Coating
Description
Aquacoat QL-929 Single component polyurethane coating is moisture-cured high polymer waterproof coating. It can react with the moisture in the air and form a non-toxic, odorless and high elastic waterproof fillm. It is a new type of environmental-friendly waterproof coating.
Product Features
- Packed in one component and ready to use. It avoids the quality instability induced by the inappropriate compounding of two or three components.
- The performance is stable. It possesses the property of aging-resistance, acid and alkali resistance, fatigue resistance as well as high and low temperature resistance.
- Environmental-friendly.
- Good leveling property, simple construction. After coating, it will react with moisture in the air and and cure, forming a compact, seamless, tough and high elastic waterproof lm.
- It can be compound with high polymer membrane and self-adhesive modied bitumen waterproof membrane to form a compound waterproof system.
Aquacoat QL -930
Single Component, Moisture Cured,100% Polyurethane Waterproof Coating
Description
Aquacoat QL-930 is one component creamy white liquid prepared by advance technology and contemporary production unit. During coating application, water, as the curing cross-linking agent, is directly added into the coating whose active group will react with the water molecule and cure to form a rubberized waterproof lm coating.
Product Features
- Single component packing. Contains no solvent, non-toxic, odourless, not polluting, self-leveling, quick curing and simple installation.
- Strong bonding to concrete substrate. Can be easily installed on wet substrate. High tensile strength and elongation. Highly conformable & excellent adaptability to the deformation in substrate.
- Heat and cold resistant. (-40~95). Chemical corrosion resistance.
- High solid content: 92%. Less PU material per square meter.
Main Application
- Non-exposed & buried roof,
- Landscape Decks, Retaining Walls
- Water Bodies, Planter Boxes
- Sunken Areas, Bathroom & Kitchen;
- Swimming pool, Fountain pool, Bathroom pool
- Subway, tunnel and underground construction.
Installation
Substrate Preparation
All Surfaces
Concrete substrate needs to be sound, clean, uniform and regular. Fill the holes with cement mortar. The flaws such as honey comb should also be repaired. The external & internal corner are rounded. Internal corner: D50mm External corner: D10mm. Brush the rst layer then pave the non-woven reinforced layer. Permeate the reinforced layer with PU material thoroughly..
Application
Firstly apply the stirred polyurethane waterproong coating over special positions like the external and internal reinforcement as well as penetrations like through-wall pipe. Afterwards, for widespread coating. Use brush or rubber scraper to brush the substrate evenly. Apply the second layer provided the rst layer is cured. The coating direction is vertical to the first one and then the third layer direction is the same as the first one. After curing, it will form a complete seamless waterproof rubber lm which will bond strongly to the substrate. Before protection, attention must be given not to damage the waterproong membrane with hard objects.
Coating Interval time: Depends on the application site but typically surface drying time is about 12 hours. Subsequent coats of PU should be applied when the preceding coat becomes tack free.
Main Application
- Basement retaining wall and slab
- Swimming pool, water bodies
- Bathroom, balcony, wet area and planter box
- Water retaining structure
- Parking deck
Installation
Substrate Cleaning & Checking
- Substrate Repair
- Coating Preparation
- Joints Treatment
- Internal & External Corner Reinforcement
- First Widespread Coating
- Second Widespread Coating (Direction is Vertical to the First Coating)
- Third Coating(The Direction is The Same as the First Coating)
- Quality Check & Repair
- Impounding Test
- Acceptance
Application
Firstly apply the stirred polyurethane waterproofing coating over special positions like the external and internal reinforcement as well as penetrations like through-wall pipe. Afterwards, for widespread coating. Use brush or rubber scraper to brush the substrate evenly. Apply the second layer provided the rst layer is cured. The coating direction is vertical to the rst one and then the third layer direction is the same as the rst one. After curing, it will form a complete seamless waterproof rubber lm which will bond strongly to the substrate. Before protection, attention must be given not to damage the waterproofing membrane with hard objects.
Coating Interval time: Depends on the application site but typically surface drying time is about 12 hours. Subsequent coats of PU should be applied when the preceding coat becomes tack free.
Aquacoat QL-988A
2 Component Flexible Cementitious Waterproof Coating
Description
Aquacoat KS-988A, is a 2 component acrylic modied cementitious waterproong system. It is two component high polymer coating material of organic liquid and inorganic powder. After mixing and stirring in a specied proportion, apply slurry on the substrate by trowel or brush to form a hard and fexible waterproof coating. It is widely used in building, road, bridge, culvert, decoration and water construction. The present waterproof system is preferred to the indoors which is not soaked in water for long time. It can be compounded with other material in the roof construction.
Product Features
- No toxic, no hazard, no pollution,environmental-friendly, safety use.
- Good adhesion, tough and strong, excellent durability and water resistance.
- It is possible to apply directly to moist (no water) and dry substrate.
- The coating lm has high tensile strength, tough, water resistant and durable.
- Directly construct on facade, slope and top with no owing. Simple construction.
- Good weather resistance. It is no need to make the protective layer on the outdoor roof.
- Possess excellent bonding ability and water resistance, great afnity to material like cement mortar and ceramic tile.